2024 Toro Greensmaster® TriFlex™ Series 3420 (04540)

Information

2024 Toro Greensmaster® TriFlex™ Series 3420 (04540)

The Greensmaster® TriFlex™ Mowers were designed to take precision cutting on a greens mower to a completely new level. Adopting the proven Flex suspension, the cutting units float freely over contours and undulations of the green resulting in a superior quality of cut and aftercut appearance. Improved serviceability is another major advantage of the TriFlex™ models. The tool-free, quick-change cutting units make servicing the cutting units fast and easy and a lift-gate footrest provides easy access to the center cutting unit.

Features may include:

Lift-In-Turn Cutting Units
  • The suspension system is designed to provide a slight lift to the inside of the cutting units during turns to deliver a consistently level cut and to reduce "triplex ring" for improved playability and turf health.
Faster Transport Speeds
  • Ten miles per hour (16.1 km/h) transport speeds will allow you to stay ahead of golfers and get more greens cut in a shorter time.
DPA Cutting Units
  • The most advanced cutting unit in the industry:Only two adjustmentsSuperior height-of-cut retentionNo daily greasing (stainless steel bearings)Consistent cutting edge regardless of reel wear (patented)Smallest bedknife increment adjustments .007inch (.178mm)
Tool-Free, Quick-Change Cutting Units
  • A single operator can go from cutting Greens at 0.125" (3.2 mm) to cutting a Fairway at ¾" (19 mm) in just minutes. The tool-free, quick-change cutting units make it as easy as 1-2-3.
Exclusive Lift-Gate Footrest
  • Easy access to the center cutting unit facilitates routine maintenance and repairs, simplifies adjustments, and eliminates the need to put the traction unit on a lift for cutting unit service saving you time, money, and frustration.

Photos

Highlights

  • Essex Junction, Vermont
  • 2024
  • Toro
  • Greensmaster® TriFlex™ Series 3420 (04540)
  • Kubota® D902, Tier 4i
  • Diesel
  • Available
  • 80.83" (205 cm) | of Cut Range: Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is 0.062" - 0.297" (1.6 - 7.5 mm). With high HOC kit, range is 0.297" - 1.0" (7.5 - 25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.

Specifications

  • 2024
  • Toro
  • Greensmaster® TriFlex™ Series
  • 3420 (04540)
  • Zero-Turn Mower
  • Kubota® D902, Tier 4i
  • Liquid Cooled
  • 24.8 HP (18.5 kW) @ 3600 rpm
  • 3-cylinder
  • 2880 high idle, 1560 rpm low idle
  • 55.0 cu-in. (902 cc)
  • Diesel
  • Diesel | Implement: Single gear pump, valve block, series reel drive to 3 reel motors. | Traction Drive: 2WD
  • No-tool quick adjust steering arm position with power assist allowing a wide range of operator sizes. Steering cylinder has a through shaft design for precise straight line tracking.
  • 2WD
  • Off - On.
  • Hand-actuated parking brake lever with two 6" (15.2 cm) diameter drum brakes mounted on the front wheel motors.
  • 12V
  • Frequency/Backlapping: Approximately 2050 RPM at 2850 engine RPM. Adjustable. Backlapping standard. | System: Maintenance-free 12-volt battery with 585 minimum CCA at 0° F (-17.7° C) and 95 minutes minimum reserve capacity at 85° F (29.4° C). 60 amp alternator, circuit fused at 60 amps. Seat switch. High temperature engine shut down. Harness terminals, fuse slot.
  • 19" x 10.5" - 8", 4-ply, Smooth Tread
  • 19" x 10.5" - 8", 4-ply, Smooth Tread
  • Ground Speed - Forward: 0 - 10 mph (0 - 16.1 km/h) | Mowing Speed: 0 - 5 mph (0 - 8 km/h)
  • Sound Power: Sound level of 84 dB(A) at operator’s ear under normal conditions.
  • Weldment shaft: 1.375" (35 mm) | Reel Diameter: 5" (13 cm)
  • Blade: 21" (53.3 cm) | Product: 98" (249 cm)
  • 4.5" (11.4 cm)
  • 80.83" (205 cm) | of Cut Range: Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is 0.062" - 0.297" (1.6 - 7.5 mm). With high HOC kit, range is 0.297" - 1.0" (7.5 - 25.4 mm). Effective HOC may vary depending on turf conditions and bedknife installed.
  • 70.62" (179 cm) with reels
  • 48.6" (123 cm)
  • 59" (150 cm)
  • 6 U.S. gal. (22.7 L)
  • 1,286 lbs. (586 kg)
  • Bedknife: Replaceable single edged EdgeMax™ Microcut Bedknife is standard. | Blade Style/Type: Reel | Number of Blades: 11, 14, 8
  • Cutting Unit Type/Configuration: Triplex, balanced cutting units with precision die-cast aluminum cross member with two bolt-on die-cast aluminum side plates. Cutting units feature quick disconnect for removal/installation and are interchangeable to all positions. Double A-Arm Suspension utilizing sealed ball joints allows free cutting unit motion in pitch and yaw. Links system for the roll. The basket is directly mounted to the cutting unit displacing weight evenly over front and rear rollers. (patented)
  • InfoCenter™: Onboard LCD shows gauges, alerts/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm, voltage, functional control status, parking brake applied, reel speed setting, backlap control. Clip control setting.