2024 Toro Greensmaster® eTriFlex® Series 3360 (04580)

2024 Toro Greensmaster® eTriFlex® Series 3360 (04580)

Swipe to View More

  • Year 2024
  • Make Toro
  • Model Greensmaster® eTriFlex® Series
  • Engine Kawasaki®
2024 Toro Greensmaster® eTriFlex® Series 3360 (04580)

2024 Toro Greensmaster® eTriFlex® Series 3360 (04580)

2024 Toro Greensmaster® eTriFlex® Series 3360 (04580)

The Greensmaster® eTriFlex® models carry no hydraulic fluid and utilize all-electric components for traction, steering, lift and cutting. These EnergySmart® models are operationally friendly with noticeable noise reductions, operational cost savings, and other meaningful improvements to complement the ever-important enhancements in cutting performance.

Combining the innovative, Double A-Arm Suspension System with industry-leading Flex technology, the cutting units float freely over any terrain. The new Radius Dependent Speed (RDS™) System, in combination with the Lift-In-Turn cutting unit leveling feature virtually eliminates the effect known as “Triplex-Ring”. This substantially improves both the aesthetics and playability of the green.

Superior cutting performance is only the beginning. The patented Lift-Gate Footrest, Tool-Free QuickChange™ cutting units, Automatic “Slow-in-Turn” during Transport and Auto-Brake on Operator Dismount are just a few of the many new features that provide added versatility, simplified service, and ultimately, more productivity.

Features may include:

All-Electric Reel Drive
  • If the operator leaves the seat when the mower is running and fails to engage the parking brake, the system will sense it and automatically engage the parking brake to ensure the operator’s safety and avoid the machine rolling away.
Superior Clippings Capture
  • The 3370 & 3360 eTriFlex models run at an amazingly quiet noise level 66.5 & 73 dBA (respectively) which minimizes early morning disturbances and results in 50% lower perceived bystander noise level.
Balloon Style Tires
  • Superior contour following capability utilizes an integrated "Flex" linkage system to allow cutting units to pivot around the center of the front roller to master undulations and prevent side-to-side scrubbing of the putting surface.
No Onboard Hydraulic Fluid
  • Eliminates clip marks at the startup of a mowing pass and provides braking power to stop reels from spinning when cutting units are disengaged for safer operation.
Auto-Brake on Operator Dismount
  • The suspension system is designed to provide a slight lift to the inside of the cutting units during turns to deliver a consistently level cut and to reduce "triplex ring" for improved playability and turf health.

Engine

Cooling Air Cooled
Engine Kawasaki®
Engine Power 14.5 HP (10.8 kW) @3600 rpm
Cylinder Liners twin
Governor 2400 rpm
Displacement 36.8 cu-inch (603cc)

Fuel System

Fuel Type Hybrid | gasoline

Drivetrain

Drivetrain Hybrid | Implement: Three, 48V (1.1 KW), air-cooled brushless permanent magnet reel motors with separable controller. | Traction Drive: 2WD
Steering 48V System for traction motor circuit, steering motor circuit, cutting unit motor circuit and lift / lower actuator circuit. 12V system for primary controls and brake actuator.
Drive System Positive 2WD traction drive: Two, brushless permanent magnet traction motors coupled to a gearbox. 3WD. (patent-pending).

Brakes

Parking Brake Traction motor regenerative braking; foot pedal service/parking brake, linear-actuated automatic parking brake.
Brake System Type linear-actuated automatic parking brake.

Battery

Battery 12V

Electric

Charging System Off-board high efficiency 1200W smart charger. - AC input voltage 100-240VAC - AC input Frequency 50/60 Hz - Max input Current 14 A - Max charge time, empty to full: 9 hrs.
Electrical Frequency/Backlapping: 200–520 RPM | Cutting Unit Lift/Lower: 48V | System: 48V System for traction motor circuit, steering motor circuit, cutting unit motor circuit and lift / lower actuator circuit. 12V system for primary controls and brake actuator.
Generator 48V 5400W air cooled brushless permanent magnet motor in parallel with four 12V 33AH AGM batteries (connected in series). Generator is used to start engine.

Wheels & Tires

Tires, Front Specification 19" x 10.5" - 8", 4-ply, Smooth Tread
Tires, Rear Specification 19" x 10.5" - 8", 4-ply, Smooth Tread

Operational

Operating Speed Ground Speed - Forward: 0 - 10 mph (0 - 16 km/h) | Ground Speed - Reverse: 0 - 5 mph (0 - 8 km/h) | Mowing Speed: 0 - 5 mph (0 - 8 km/h)

Chassis

Frame Type Three tie-down locations (2 side, 1 rear).

Performance

Noise Level Sound Power: 91 db(A) Sound Power at Operator's Ear: 73 db(A) Sound Power to Bystander: 25 ft – 78 db(A), 50 ft – 73 db(A), 100 ft – 66 db(A)

Dimensions

Dimensions Blade: 5" (13 cm) | Weldment shaft: 1.375" (35 mm) | Reel Diameter: 5 in. (12.7cm) | Turning Circle (Diameter): 69.8" (182 cm)
Length Blade: 21" (53.3 cm) | Product: 98" (249 cm) with baskets
Ground Clearance 3.8" (9.7cm)
Height 80.8" (205 cm) | of Cut Range: Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is 0.062" - 0.297" (1.6 - 7.5 mm). With high HOC kit, range is 0.297" - 1.0" (7.5 - 25.4 mm). Effective HOC may vary depending on turf conditions and roller/bedknife installed.
Overall Width 70.9" (180 cm)
Wheelbase 49.8" (126.5 cm)
Cutting Width 59" (150 cm)

Capacities

Fuel Capacity 4.9 U.S. gal. (18.5 L)

Weights

Weight Mow: 1,354 lbs (614 kg) | Transport: 1,625 lbs (737 kg)

Features

Features Bedknife: Aggressiveness stays constant throughout the life of the reel regardless of reel or bedknife wear. Patented design. | Blade Style/Type: Reel | Number of Blades: 11, 14, 8
Construction Material Cutting Unit Type/Configuration: Triplex, balanced cutting units with precision die-cast aluminum cross member with two bolt-on die-cast aluminum side plates. Cutting units feature quick disconnect for removal/installation and are interchangeable to all positions. Double A-Arm Suspension utilizing sealed ball joints allows free cutting unit motion in pitch and yaw. Links system for the roll. The basket is directly mounted to the cutting unit displacing weight evenly over front and rear rollers. (patented)
Gauges InfoCenter™: Onboard LCD display shows gauges, alerts/faults, service reminders, electrical system diagnostics, low oil pressure, alternator, engine hours, engine rpm, voltage, functional control status, parking brake status, reel speed setting, backlap control, clip control, calibration of 48V components, advanced machine diagnostics.

Product Photography